
Add to Cart
High performance, reliable, underground mining machine, jumbo drill machine.
Drilling jumbo is a mining equipment widely used in underground mining if mining is done by drilling and blasting, such as coal, lead and zinc mine. It is also used in tunnel ,culvert tunnelling, railway, highway engineering with advanced hydraulic system and anti-clamping bit device ,the rock drilling rig is a modern equipment of convenient, safe and reliable operation. Equipped with the best international brand drifter, our drilling jumbo can reach 0.8~2m/min drilling speed, and can be applied to 6.1x6.08m tunnel section.
Features
1.Hydraulic boom
Hydraulic boom with double tripod suspension for accurate hydraulic parallel holding in all directions, direct, fast, easy operation, good accuracy and accurate positioning between holes;
Telescopic boom make up of the angle when drilling the hole of bottom and top, thus no blind angle left.
Rotary actuators with high rotation torque, high load capacity.
2.Drifter
International first class drifter with high hardness, high drilling speed, low drilling tool wastage and low failure rate and etc.
3.Carrier
Sturdy, articulated carrier with four-wheel drive, powered by diesel engine, high speed and flexible transition improve the working efficiency;
Central lubrication system;
Four jacks for stable set up.
4.Control system
Hydraulically controlled drilling system which incorporates the anti-jamming function rotation pressure controlled feed(RPCF); Impact, rotation and feed adopt separate hydraulic pump, independent control loop ensure ensure the stable power output.
5.General
Automatically controlled cable reel;
FOPS telescopic protective roof;
Electrically driven piston compressor.
ITEM | SPECIFICATION | ||
Machine | Overall dimension mm | 11070×1700×2150/2850 | |
Tunnel section(w×h)m | 3×3-6.6×6.3 | ||
Hole diameter mm | Φ41-Φ76
| ||
Length of drill rod | 3700/4300 | ||
Hole depth mm | 3405/4000 | ||
Length of feeder | 5555/6155 | ||
Drilling speed m/min | 0.8-2 | ||
Power of motor kW | 55(main motor) | ||
Volume of oil tank L | 200 | ||
Weight t | 12500 | ||
Boom | Rock drill | Model | HC50 |
Impact power kW | 13 | ||
Working impacting pressure bar | 13 | ||
Impact frequency | 52 | ||
Rotating speed(r/min) | 195 | ||
rotation | ±180° | ||
Up/down | down 90°,up3° | ||
Boom extension mm | 1190 | ||
Compensation of feeder
| 1550 | ||
Chassis
| Diesel engine Power KW | 53kW@2200rpm | |
Steering angle | ±40° | ||
Specification of tyre | 9x R20 | ||
Rear axle swing angle | ±7° | ||
Approach angle/Departure angle° | approach angle 22° departure angle17° | ||
Turning radius m | Inner 3m; External 5.5m. | ||
Traveling speed km/h | 12 | ||
Ground clearance | 362mm | ||
Braking way | Full closed, wet braking | ||
Volume of hydraulic oil tank L | 200 | ||
Volume of fuel tank L | 60 | ||
Water system | booster water pump | Centrifugal | |
Volume | 67 L /min | ||
Power of motor | 2.2kw | ||
Working water pressure Mpa | 0.8-1.2 | ||
Air system | Air compressor | Fusheng V80 | |
Volume L/min | 300 | ||
Electric motor kW | 2.2
| ||
Working air pressure Mpa | 0.2-0.8 | ||
Electric system | Total Power of Electric Motor kW | 59(55+4) | |
Power supply | 380V | ||
Rotating speed of electric motor r/min | 1483 | ||
Travelling Light W | 8×65W, 12V | ||
Working light W | 2×150W 220V |